International ServiceMaxx 2016 diagnostic and programming service tool J1939\J1708 (Offline)+keygen

ServiceMaxx version 43.26 (release date 12-09-2015)

ServiceMaxx J1708

    Connection / Communication:
        9-Pin Type I (Black)
            Protocol CAN J1708 @ 250K Baud
        9-Pin Type II (Green)
            Protocol CAN J1708 @ 250K Baud
    Engine Detection Target:
        Engine Serial Number
    Supported Legacy Engines (1994 - 2006):
        Pre-MaxxForce Engines
            I63BX:3 Box I6 (1994 - 1997)
            V83BX:3 Box V8 (1994 - 1997)
            i308:DLC I6 (1998 - 2004)
            T444E:DLC V8 (1998 - 2004)
            I313:DLCII I6 (2005 - 2006)
            V128:DLCII V8 (2005 - 2006)
            V126:DLCII V6 (2005 - 2006
                  

ServiceMaxx version 43.26 (release date 12-09-2015)

ServiceMaxx J1939

    Connection / Communication:
        9-Pin Type I (Black)
            Protocol CAN J1939 @ 250K Baud
            K-line (MWM Engines)
        9-Pin Type II (Green)
            Protocol CAN J1939 @ 250K Baud
            Protocol CAN J1939 @ 500K Baud (2016 North American engines forward)
            KWP2000 K-line (For MWM Engines)
    Engine Detection Target:
        Engine Calibration ID (Production Calibration only)
        CAT Engines also use Parameter: 88/01
    Supported Engines:
        North American
            v155:MaxxForce 5 (2007 - 2009)
            v134:MaxxForce 7 (2007 - 2009)
            v152:MaxxForce 7 (2010 - 2012)
            v179:MaxxForce 7 (2013 - )
            i326:MaxxForce DT, 9, 10 (2007 - 2009)
            i334:MaxxForce DT, 9 ,10 (2010 - 2012)
            i367:MaxxForce DT, 9, 10 (2013)
            i766:MaxxForce 11, 13 (2008 - 2009)
            i783:MaxxForce 11, 13 (2010 - 2012)
            B764:MaxxForce 11, 13 (2013 - 2013.5)
            i770:MaxxForce 15 (2010 - 2013)
        SCR Engines
            I746:N9, N10 SCR (2014 - )
            B718:N13 SCR (2013 - 2014)
            B745:N13 SCR (2015 - )
        Removed Engines:
            I63BX:3 Box I6 (1994 – 1997)
            V83BX:3 Box V8 (1994 – 1997)
            I308:DLC I6 (1998 – 2004)
            T444E:DLC V8 (1998 – 2004)
            V126:DLCII V6 (2005 – 2006)
            I313:DLCII I6 (2005 – 2006)
            V128:DLC V8 (2005 – 2006)
    Engine list below is with Engineering Access:
        Military Engines
            Mil13:MaxxForce 12.4D
        CAT Engines:
            CT11:CAT CT11/13 (2010 - 2012)
            CT764:CAT CT13 (2013)
            CT15:CAT CT15
            CT718:CAT CT13 SCR (2013 - 2014)
            CT745:CAT CT13 SCR (2015 - )
        Global Engines:
            I341:DLCII I6 Export (2007 - )
            I716:N13 (Euro V)
            MWM:MaxxForce 3.0H (Euro III - P418V50)
            MWM:MaxxForce 7.2/4.8 H (Euro III - P625V13)
            MWM:MaxxForce 7.2/4.8 H (Euro IV - P800V24)
            MWM:MaxxForce 7.2/4.8 H (Euro IV - P800V32)
            MWM:MaxxForce 7.2/4.8 H (Euro V - P1090V52)
            MWM:MaxxForce 3.2 H (Euro III)
            MWM:MaxxForce 3.2 H (Euro IV)
            MWM:MaxxForce 3.2 H (Euro V)
        Engineering Engines:
            B786N13 (2017 - )
        Removed Engines (Did not go into Production):
            I355:MaxxForce 9.3 (Euro V)

Software Fixes:

    Software Lag or Slow response Issue
        Change the way Requested signals are handled.
    ServiceMaxx version 42.18 (release date: 08/05/2015)
        Software Enhancements
            MaxxForce 11/13 (2010 - 2013)
                DOC Efficiency Test (Field Service Access)
            MaxxForce DT/9/10 (2010 - 2013)
                DOC Efficiency Test (Engineering Development)
                Air Management Performance Test (Engineering Development)
                Trip Report
                Remove Trip Report (Not Supported)
            MaxxForce 11/13 (2010-13), N13 SCR (2014 - 2015)
                Stand Alone Real Time Clock
                Time Synchronization Check
                Multi Cylinder Cutout enhancements
                Add Start and End temperatures to Test Results
                Trip Report enhancement
                Remove MaxxForce name from Report Printout
                Correct Reset for Trip Active Regen Count
            N9/N10 SCR (2014 - ), N13 SCR (2013 - 2015)
                DPF Regeneration session
                    Session update (Move Test Inhibitors to Default view)
            N13 SCR (2017) Engineering Access only
                Add database Support: Signals/Parameters/DTCs
            Snapshot recordings enhancement
                Remove Min/Max/Average from recordings
                Remove Negative counter
            History Support (Phase 1)
                Writes Engine information to history.
                Vehicle Identification number
                Engine Serial Number
                Calibration ID
                Customer Password – When entered by user.
            Slow Network Alert
                Popup Alert message if slow Network is detected during software updates.
        Software Fixes
            Signal display and Recording
                Display Proper Symbols
                Display correct value in Graphs
            MaxxForce 11/13 (2010 - 2013), N13 SCR (2014 - 2015)
                Multi Cylinder Cutout enhancements
                Refresh Test Results panel if test is re-started.
                Test Abort Message Correction
                High Pressure Pump Test
                Air Management Test
                Intake Air Heater Test

 without needing a net JAVA iinternet connection

Contact Information:

my email: autotruckepc@gmail.com
Skype:  autotruckepc
Web site: www.autotruckepc.com
If you have any problem, please do not hesitate to contact us.

Shipment Note:

If your package shipped by Express Delivery, please give us a valid delivery phone number, and also a full and accurate shipping address